衛生設備用冷熱混合水龍頭檢測

衛生設備用冷熱混合水龍頭檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 16662-2008建筑給水排水設備器材術語

本標準規定了建筑給水排水設備和器材，包括衛生器具，水嘴，加壓、調節和貯存設備，加熱貯熱設備，地漏，檢查井，建筑水處理設備，游泳池、游樂池設備，冷卻設備，水景設備，雨水利用設備，管材，管件，閥門，計量、檢測儀表等方面的專用術語。本標準適用于建筑給水排水設備和器材的專用術語。

GB 50096-2011住宅設計規范

為保障城鎮居民的基本住房條件和功能質量，提高城鎮住宅設計水平，使住宅設計滿足安全、衛生、適用、經濟等性能要求，制定本規范。本規范適用于城鎮新建、改建和擴建住宅的建筑設計。住宅設計必須執行有關方針、政策和法規，遵守安全衛生、環境保護、節約用地、節約能源資源等有關規定。 住宅設計除應符合本規范外，尚應符合現行有關標準的規定。

GB 50333-2013醫院潔凈手術部建筑技術規范

本規范適用于醫院新建、改建、擴建的潔凈手術部工程的設計、施工和驗收。

GB 50555-2010民用建筑節水設計標準

本標準適用于新建、改建和擴建的居住小區、公共建筑區等民用建筑節水設計,亦適用于工業建筑生活給水的節水設計。

GB/T 50604-2010民用建筑太陽能熱水系統評價標準

為貫徹實施能源節約、環境保護、建設節約型社會，推進在建筑上利用太陽能熱水系統，規范民用建筑太陽能熱水系統的評價，規定本標準。本標準適用于評價新建、改建和擴建民用建筑上使用的太陽能熱水系統，以及在既有民用建筑上增設、改造的太陽能熱水系統。評價太陽能熱水系統應依據因地制宜的原則，結合建筑類型及其所在地域的太陽能資源、自然環境、經濟發展水平、社會習俗等特點進行評價。民用建筑太陽能熱水系統的評價，除應符合本標準外，尚應符合現行有關標準的規定。

GB 50687-2011食品工業潔凈用房建筑技術規范

本規范適用食品加工和生產的新建、改建和擴建廠房中潔凈用房的設計、施工、工程檢測和工程驗收。

GB 50881-2013疾病預防控制中心建筑技術規范

1.0.1 為適應我國疾病預防控制事業的發展，保證省、地(市)、縣級疾病預防控制中心(以下簡稱 “疾控中心”)建筑在設計、施工和驗收方面符合使用功能、安全、衛生、節能、環保等的基本要求，制定本規范。1.0.2 本規范適用于疾控中心建筑的新建、改建和擴建工程的建筑設計、施工和驗收。本規范不適用于生物安全四級實驗室。1.0.3 疾控中心的建設，必須堅持科學、合理、實用、規范的原則，應正確處理現狀與發展、需要與可能的關系。應在滿足基本功能、實現工藝設計要求的同時，體現標準化、智能化、人性化的特點。1.0.4 疾控中心的建設應符合現行有關疾病預防控制中心建設標準的規定。1.0.5 有生物安全要求的實驗室，應符合現行標準《生物安全實驗室建筑技術規范》GB 50346、《實驗室生物安全通用要求》GB 19489的有關規定。動物實驗室應符合現行標準《實驗動物環境及設施》GB 14925及《實驗動物設施建筑技術規范》GB 50447的有關規定。1.0.6 疾控中心建筑的設計、施工和驗收除應執行本規范外，尚應符合現行有關標準的規定。

GB/T 51100-2015綠色商店建筑評價標準

本標準適用于綠色商店建筑的評價。

GB/T 51293-2018城市軌道交通給水排水系統技術標準

本標準適用于城市軌道交通工程給水排水系統的設計、施工及驗收。

JGJ/T 229-2010民用建筑綠色設計規范

本標準適用于新建、改建和擴建民用建筑的綠色設計。

DIN EN 200-2008衛生設備用水龍頭.1型和2型的供水系統用單一水龍頭和組合水龍頭.通用技術規范

This European Standard specifies: a) the field of application for pillar taps, bib taps, single and multi-hole combination taps for use in: 1) a supply system of Type 1 (see Figure 1); 2) a supply system of Type 2 (see Figure 2); b) the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, endurance and acoustic characteristics of nominal size 1/2 and 3/4 single taps and combination taps; c) test methods to verify the characteristics. The tests described in this European Standard are type tests (laboratory tests) and not quality control tests carried out during manufacture.) This European Standard applies to draw-off taps (single taps and combination taps) for use with sanitary appliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms etc.) and in kitchens, i.e. for use with baths, wash basins, bidets, showers and sinks. Figure 1 shows a supply system of Type 1 with a pressure range of (0,05 to 1,0) Mpa [(0,5 to 10) bar]. Figure 2 shows a supply system of Type 2 with a pressure range of (0,01 to 1,0) Mpa [(0,1 to 10) bar]. This European Standard applies to sanitary draw-off taps of nominal size 1/2 and 3/4 (PN 10). The conditions of use and classifications are given in Table 1. The Table 2 gives the performance characteristics to be noted if the tap is used outside the recommended operating range.

DIN EN 817-2008衛生用水龍頭.機械混合閥(PN 10).一般技術規范

This European Standard specifies:-- the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, endurance and acoustic characteristics with which mechanical mixing valves need to comply;-- test methods to verify the characteristics.The tests described in this European Standard are type tests (laboratory tests) and not quality control tests carriedout during manufacture.This European Standard applies to PN 10 mechanical mixing valves for use with sanitary appliances installed inrooms used for bodily hygiene (cloakrooms, bathrooms, etc.) and in kitchens, i.e. for use with baths, wash basins,bidets, showers and sinks.The conditions of use and classifications are given in O.

DIN EN 1112-2008衛生設備用水龍頭.1型和2型供水系統用衛生設備水龍頭的淋浴噴頭.一般技術規范

This European Standard specifies:-- the dimensional, leaktightness, mechanical, hydraulic and acoustic characteristics with which shower outlets shall comply;-- the procedures for testing these characteristics.This European Standard applies to shower heads and hand showers of any material used for ablutionarypurposes and intended for equipping and supplementing sanitary tapware for baths and showers.This European Standard applies to shower heads and hand showers connected downstream of the obturatorof the tapware.Integral and remote spray attachments incorporated in tapware (e.g. sink and wash basin mixing valves) arenot covered by this standard.Details of pressures and temperatures are given in Table 1.

DIN EN 15200-2007衛生設備.多功能淋浴間

This standard specifies requirements and test methods for multifunction shower cabinets (subsequently referred to as unit(s)), used for domestic purposes.This standard does not apply to shower cabinets and shower enclosures.NOTE For the purposes of this standard the term \"domestic purposes\" includes use in hotels, accommodation forstudents and similar buildings, except when special provisions e. g. medical, are required.

BS 5546-2010額定輸入不超過70kW的家用燃氣供熱水裝置的安裝和維修規范

This British Standard specifies requirements for the selection,installation, inspection, commissioning and maintenance of gas?firedwater-heating appliances, which have a rated heat input notexceeding 70 kW, based on net calorific value.It applies to water-heating appliances utilizing 1st, 2nd or 3rd familygases designed to operate in the condensing or non?condensingmode for the supply of hot water for domestic purposes in domesticdwellings or domestic dwellings in commercial premises.This standard does not apply to:a) water-heating appliances with a rated input of over 70 kW;b) hot water supply systems in multiple dwellings supplied from acentral source.It does not cover the detailed design and installation of the whole hotwater distribution system, which was specified in BS 5449.This standard applies to water-heating appliances which carry aCE mark and also to previously used water-heating appliances whichdo not carry the CE mark (see 5.3.1).

BS 6100-7-2008建筑和土木工程.詞匯.第7部分:設備

This part of BS 6100 defines terms for the systems, installations andequipment that:a) provide water, electricity, heat, warm air and gases;b) facilitate internal communication and transport, lighting and wasteremoval.This standard does not define terms outside the curtilage of premises,e.g. water supply and public health engineering, which are both coveredin BS 6100-6.

BS 6465-4-2010衛生器具.公共廁所業務守則條款

This part of BS 6465 gives recommendations on the location, numbers,siting, design and management of public toilets. It is applicable to theprovision of new facilities and to the retention and refurbishment ofexisting facilities.This standard is applicable to the following types of public toilet facilities:a) municipal public on-street toilets;b) off-street publicly available toilets (e.g. in shopping malls);c) automatic public conveniences (APCs);d) street urinals;e) facilities for disabled people, from the point of view of scale ofprovision and location;f) baby changing and ancillary toilet facilities.

BS EN 200-2008衛生用水龍頭.1型和2型供水設備用單一水龍頭和組合水龍頭.通用技術規范

This European Standard specifies:a) the field of application for pillar taps, bib taps, single and multi-hole combination taps for use in:1) a supply system of Type 1 (see Figure 1);2) a supply system of Type 2 (see Figure 2);b) the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, enduranceand acoustic characteristics of nominal size ? and ? single taps and combination taps;c) test methods to verify the characteristics.The tests described in this European Standard are type tests (laboratory tests) and not quality control tests carriedout during manufacture.This European Standard applies to draw-off taps (single taps and combination taps) for use with sanitaryappliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms etc.) and in kitchens, i.e. for use withbaths, wash basins, bidets, showers and sinks.Figure 1 shows a supply system of Type 1 with a pressure range of (0,05 to 1,0) Mpa [(0,5 to 10) bar].Figure 2 shows a supply system of Type 2 with a pressure range of (0,01 to 1,0) Mpa [(0,1 to 10) bar].This European Standard applies to sanitary draw-off taps of nominal size ? and ? (PN 10).The conditions of use and classifications are given in Table 1. The Table 2 gives the performance characteristics tobe noted if the tap is used outside the recommended operating range.

BS EN 246-2003衛生設備用水龍頭.流速調節器通用規范

This European Standard specifies:\n— the dimensional, mechanical, hydraulic and acoustic characteristics with which flow rate regulators should comply;\n— the procedures for testing these characteristics. This European Standard is applicable to:\n— flow rate regulators intended to be mounted on tapware used with sanitary appliances in toilets, washrooms and kitchens (single taps, combination tap assemblies, mechanical mixing valves, thermostatic mixing valves);\n— flow rate regulators used under the following pressure and temperature conditions:\nFlow rate regulators can only be connected downstream of the obturator of the tap.

BS EN 806-2-2005人類消費用水的建筑物內部輸水設備規范.設計

This document gives recommendations, and specifies requirements, on the design of potable water installations within buildings and for pipework outside buildings but within the premises (see EN 806-1) and applies to new installations, alterations and repairs.