花灑和噴淋軟管檢測

花灑和噴淋軟管檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 33733-2017廚衛五金產品術語與分類

本標準規定了廚房和衛生間及類似場合使用的五金產品的術語、定義及分類。本標準適用于廚衛五金產品的設計、生產、貿易、質量檢驗、科學研究、教學等領域。

QB/T 4050-2010淋浴器

本標準規定了淋浴器（淋浴柱）的產品分類、要求、試驗方法、檢驗規則及標志、包裝、運輸、貯存。 本標準適用于公稱壓力不大于1.0MPa，水介質溫度不大于90℃條件下，安裝在盥洗室(洗手間、浴室)、淋浴房等衛生設施上使用的淋浴器。 本標準不適用于自帶加熱裝置的淋浴器。

DIN EN 12259-1-2006固定滅火系統.噴灑器和噴水系統用元部件.第1部分:噴灑器

This European Standard specifies requirements for construction and performance of sprinklers which are operated by a change of state of an element or bursting of a glass bulb under the influence of heat, for use in automatic sprinkler systems. Test methods and a recommended test schedule for type approval testing are also given.#,,#

BS EN 1112-2008衛生開關龍頭.1型和2型供水系統用衛生開關龍頭的淋浴出口.通用技術規范

This European Standard specifies:? the dimensional, leaktightness, mechanical, hydraulic and acoustic characteristics with which showeroutlets shall comply;? the procedures for testing these characteristics.This European Standard applies to shower heads and hand showers of any material used for ablutionarypurposes and intended for equipping and supplementing sanitary tapware for baths and showers.This European Standard applies to shower heads and hand showers connected downstream of the obturatorof the tapware.Integral and remote spray attachments incorporated in tapware (e.g. sink and wash basin mixing valves) arenot covered by this standard.Details of pressures and temperatures are given in Table 1.Table 1 — Conditions of use/Classifications

BS EN 14506-2005防飲用水回流污染設備 自動排水道 C型、H系列

This document specifies:a) field of application;b) requirements for automatic diverters;c) dimensional and the physico-chemical properties and the properties of general hydraulic, mechanical andacoustic design of automatic diverters;d) test method and requirements for verifying these properties. For sanitary tapware (see Clause 2) with integrateddevices, the automatic diverter is only considered to be a backflow protection device if it haspassed the requirements of this document and additionally those of the applicable product standard forthe draw off tap or mixing valve;e) marking and presentation;f) acoustics.This document specifies the characteristics of automatic diverters suitable for use in drinking water systems atpressures up to 1 MPa (10 bar) and temperatures up to 65 °C and for 1 h at 90 °C. They are intended only forinstallation with no downstream closing device.This document is applicable to the product type indicated as follows:i) integrated in spout (outlet);ii) integrated in the mixing body;iii) non-integrated (part of a set) above the maximum water level.This document is not applicable to the product type non-integrated below the maximum water level.