氣缸活塞桿檢測

氣缸活塞桿檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 2350-2020流體傳動系統及元件 活塞桿螺紋型式和尺寸系列

本標準規定了以液壓油(液)或壓縮空氣為工作介質的液壓缸、氣缸活塞桿螺紋的常用系列，以及為活塞桿螺紋裝配擰緊所設置的扳手面、扳手孔尺寸。本標準適用于液壓缸、氣缸活塞桿的外部連接螺紋。

GB/T 25268-2010橡膠 硫化儀使用指南

本標準給出了用硫化儀測定橡膠混煉膠硫化特性的指南。

GB/T 33924-2017氣缸活塞桿端球面耳環安裝尺寸

本標準規定了氣缸活塞桿端球面耳環的安裝尺寸，以滿足其互換性要求?；钊麠U端球面耳環專門設計用于按照ISO 6430、ISO 6432和ISO 15552制造的1 MPa系列氣缸，但也可應用在其他方面。安裝在氣缸活塞桿端的球面耳環，用于氣缸在擺動和傾斜運動時的機械連接，其根據符合ISO 6430、ISO 6432和ISO 15552中規定的氣缸內徑和壓力所產生的大作用力設計。

GB/T 33927-2017氣缸活塞桿端環叉安裝尺寸

本標準規定了氣缸活塞桿端環叉的安裝尺寸以滿足互換性要求。這類氣缸活塞桿端環叉主要用于按照ISO 6430、ISO 6432和ISO 15552制造的1 MPa系列氣缸，但也可應用于其他方面。安裝在氣缸活塞桿端的環叉是用于氣缸力的機械傳輸。氣缸活塞桿端環叉根據符合ISO 6430、ISO 6432和ISO 15552規定的氣缸內徑和壓力所產生的大作用力設計。

MT/T 813-1999井內懸吊式氣動抓巖機通用技術條件

本標準規定了井內懸吊式氣動抓巖機的定義、基本參數、技術要求、試驗方法、檢驗規則和標志、包裝、運輸與貯存。\t本標準適用于井內懸吊式氣動抓巖機(以下簡稱抓巖機)。

QB/T 1757-1993造紙機械.橫管連續蒸煮器

本標準規定了ZJL5型橫管連續蒸煮器的產品分類、技術要求、試驗方法、檢驗規則、標志、包裝、運輸、貯存。\t本標準適用于以竹片、竹絲、稻草、麥草、蘆葦、荻、蔗渣、棉桿、麻桿等非木纖維為原料生產紙漿(也適用于以木片生產化學機械漿)的ZJL5型橫管連續蒸煮器。

SY/T 5027-2012石油鉆采設備用氣動元件

本標準規定了石油鉆采設備用氣動元件(包括控制閥、氣缸和輔助元件,以下簡稱氣動元件)的術語和定義、符號,分類與型號編制,基本參數,技術要求,試驗方法,檢驗項目,標志和使用說明書,包裝與貯存。本標準適用于以壓縮空氣為工作介質,公稱壓力不大于1MPa的氣動元件的設計、制造及檢驗。

JGJ 160-2016施工現場機械設備檢查技術規范

本規范適用于新建、擴建和改建的工業與民用建筑及市政工程施工現場機械設備的檢查。

JB/T 5923-2013氣動 氣缸技術條件

本標準規定了氣動系統中氣缸的技術要求、檢驗方法、檢驗規則及標識、包裝及貯存等、本標準適用于以壓縮空氣為工作介質,在氣壓傳動系統中使用的雙作用、缸徑為6 mm~320 mm的活塞式普通氣缸(簡稱氣缸)、

JB/T 6656-1993氣缸用密封圈安裝溝槽.型式、尺寸和公差

本標準規定了氣缸用QY形、C形、CK形、J形、ZHM形及QH形密封圈的安裝溝槽型式、尺寸和公差。 本標準適用于安裝符合JB/T 6657標準中所規定的密封圈的安裝溝槽型式、尺寸和公差。

JB/T 8884-2013氣動元件產品型號編制方法

本標準規定了氣動元件和氣動輔件型號的編制方法。本標準適用于以壓縮空氣或性能相當?shù)钠渌ぷ鹘橘|(zhì)的一般用途的氣動元件和氣動輔件。

JB/T 11066-2010梳齒榫對接機 精度

本標準規定了梳齒榫對接機的幾何精度及工作精度,并給定了相應的公差,適用于一般用途、普通精度的梳齒榫對接機。本標準只規定機床精度檢驗,不適用于機床的運動試驗(如振動、異常噪聲、零部件的爬行等檢驗)也不適用于機床的特性檢驗(如速度、進給量等),這些檢驗一般均在機床精度檢驗前進行。

JB/T 11129-2011氣缸活塞桿技術條件

本標準規定了氣缸用圓形活塞桿的外徑規格、材質、表面處理、公差（尺寸公差和形位公差）以及表面質量等要求。本標準適用于氣缸用作直線運動的圓形活塞桿。

JB/ZQ 4217-2006活塞桿外螺紋防護帽

本標準適用于冶金設備用液壓缸、氣缸活塞桿外螺紋的防護。也可用于其他缸類活塞桿外螺紋的防護。使用環境溫度為-40～+80℃。

ISO 4395-2009液壓傳動系統和組件.汽缸活塞桿端型號和尺寸

This International Standard establishes a basic series for\npiston rod end types for application on cylinders used in hydraulic\nand pneumatic fluid power systems.\nIt specifies thread dimensions and configurations for use with\nhydraulic and pneumatic cylinder piston rod ends, as well as the\ndimensions of wrench flats and hook wrench holes that are sometimes\nnecessary for the assembly of the cylinder piston rod''s threaded\nend to accessories.

ISO 4395 CORR 1-2010液壓傳動系統和組件.汽缸活塞桿端型號和尺寸.技術勘誤1

Technical Corrigendum 1 to ISO 4395:2009 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders.

GSO ISO 4395-2015液壓傳動系統和部件氣缸活塞桿端類型和尺寸

This International Standard establishes a basic series for piston rod end types for application on cylinders used in hydraulic and pneumatic fluid power systems. It specifies thread dimensions and configurations for use with hydraulic and pneumatic cylinder piston rod ends, as well as the dimensions of wrench flats and hook wrench holes that are sometimes necessary for the assembly of the cylinder piston rod’s threaded end to accessories.

DIN EN ISO 4413-2011液壓傳動.系統及其部件的一般規則和安全要求(ISO 4413-2010);德文版本EN ISO 4413-2010

This International standard specifies general rules and safe requirements for the hydraulic fluid power systems and components used on machinery as defined by ISO 12100:2010,3.1. It deals with all significant hazards associated with hydraulic fluid power systems and specifies the principles to apply in order to avoid those hazards when the systems are put to their intended use.NOTE 1 See Clause 4 and Annex A.The significant hazard noise is incompletely dealt with in this International Standard.NOET 2 Noise emission depends especially on the installation of pneumatic components or systems into machinery.This International Standard applies to the design, construction and modification of systems and their components, also taking into account the following aspects:a) assembly;b) installation;c) adjustment;d) uninterrupted system operation;e) ease and economy of maintenance and cleaning;f) reliable operation in all intended uses;g) energy efficiency; andh) environment.

DIN EN ISO 4414-2011氣壓傳動.系統及其部件的一般規則和安全要求(ISO 4414-2010);德文版本EN ISO 4414-2010

This International standard specifies general rules and safety requirements for pneumatic fluid power systems and components used on machinery as defined by ISO 12100:2010,3.1. It deals with all significant hazards associated with pneumatic fluid power systems and specifies the principles to apply in order to avoid those hazards when the systems are put to their intended use.NOTE 1 See Clause 4 and Annex A.The significant hazard noise is incompletely dealt with in this International Standard.NOET 2 Noise emission depends especially on the installation of pneumatic components or systems into machinery.This International Standard applies to the design, construction and modification of systems and their components, also taking into account the following aspects:a) assembly;b) installation;c) adjustment;d) uninterrupted system operation;e) ease and economy of maintenance and cleaning;f) reliable operation in all intended uses;g) energy efficiency; andh) environment.This International Standard does not apply to air compressors and the systems associated with air distribution as typically installed in a factory, including gas bottles and receivers.