多功能控制裝閥檢測

多功能控制裝閥檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 10827.1-2014工業車輛 安全要求和驗證 第1部分:自行式工業車輛(除無人駕駛車輛、伸縮臂式叉車和載運車)

GB 10827的本部分規定了如ISO 5053所定義的下列自行式工業車輛(以下簡稱“車輛”)的安全要求及其驗證方法:a) 平衡重式叉車;b) 前移式叉車(具有可伸縮的門架或貨叉架);c) 插腿式叉車;d) 托盤堆垛車;e) 高起升平臺搬運車;f) 操作臺起升高度不大于1 200 mm的車輛;g) 側面式叉車(單側);h) 側面堆垛式叉車(兩側和三向);i) 托盤搬運車;j) 雙向和多向運行叉車;k) 牽引力不大于20 000N的牽引車;l) 平衡重式越野叉車;m) 其他以蓄電池、柴油、汽油或液化石油氣為動力的工業車輛。對于操作臺起升高度大于1 200 mm的車輛和/或帶著載荷起升至1 200 mm以上運行的車輛,本部分應與ISO 3691-3一起使用。本部分不適用于自行式伸縮臂式叉車、無人駕駛車輛和載運車,ISO 3691-2、ISO 3691-4和ISO 3691-6分別適用于這些車輛。本部分不適用于在苛刻條件下(如極端天氣、冷庫應用、危險環境)工作的車輛,這些情況需要有特殊防護措施。本部分涉及了除以下情形外,有關機械在制造商預期用途下使用和可預見條件下誤用的,如附錄B所列的所有重大危險、危險狀態或危險事件。本部分不包括下列情況可能發生的危險:--在制造過程中;--搬運能自由擺動的懸吊載荷時;--在公路上使用時;--在潛在爆炸性環境中操作時;--在與貨架之間的單側間隙小于500 mm的狹窄通道上使用時;--駕駛拖曳載荷的坐駕式車輛時,由于采用非人類工效學姿勢而引起;--駕駛額定起重量大于10 000 kg

GB/T 14536.9-2008家用和類似用途電自動控制器. 電動水閥的特殊要求(包括機械要求)

GB 14536.1-2008中的該章，用下述內容代替：1.1本部分適用于家用和類似用途設備中或隨這些設備一起使用的電動水閥，這些設備可以是使用電、燃氣、油、固體燃料、太陽能等能源或是它們的組合，應用范圍包括加熱、空氣調節及類似用途。本部分也適用于GB 4706所涉及的各類器具用的電動水閥。1.1.1本部分包含了對水閥的電氣性能和閥的機械性能的要求，這兩者會影響水閥預期操作。1.1.2本部分適用于電動水閥固有的安全性，適用于涉及到設備保護的操作值和操作程序，適用于家用和類似用途設備中或隨這些設備一起使用的電自動控制器的試驗。對于非一般家用設備用電動閥，而這些設備是由諸如商店或輕工工廠或農場的非農場的非人員使用的，也包含在本部分范圍內。本部分不適用于專門用于工業設備的電動水閥。本部分不適用于：標稱連接尺寸在DN 50以上的電動水閥；標稱允許壓力值在1.6Mpa以上的電動水閥；食品分配器；洗滌劑分配器；蒸汽閥。在本部分中，當不會引起誤解時，下列術語有其特定含義：——“閥”一詞指電動水閥（包括起動器和閥體組件）。——“起動器”一詞意思是“電動機構或原動機構”?！伴y體”一詞意思是“閥體組件”?！霸O(shè)備”一詞包括器具和控制系統。1.1.3本部分適用于起動器和相互匹配的閥體。1.1.4本部分適用于單個的閥、作為系統部件的閥和與多功能控制器機械地組合在一起的無電氣輸出的閥。

GB/T 14536.21-2008家用和類似用途電自動控制器.電動油閥的特殊要求，包括機械要求

GB 14536.1中的該章，用下述內容代替: 代替: 1. 1本部分適用于家用和類似用途設備中或隨這些設備一起使用的電動油閥，這些設備可以是使用電、燃氣、油、固體燃料、太陽能等能源或是它們的組合，應用范圍包括加熱、空氣調節及類似用途。 本部分也適用于使用NTC或PTC熱敏電阻的電動油閥，其要求包含在附錄J中。 1.1.1本部分適用于電動油閥固有的安全性，適用于涉及到設備保護的操作值和操作程序，適用于家用和類似用途設備中或隨這些設備一起使用的電自動控制器的試驗。也適用于工業用途的，沒有相應 標準的，如中央加熱、空調、熱處理等用的電動油閥。 本部分也適用于GB 4706.1所涉及的各類器具用的電動油閥。 本部分包含了對油閥的電氣性能和閥的機械性能的要求，這兩者會影響油閥預期操作。 本部分不適用于專門用于工業設備的電動油閥。 對于非一般家用設備用電動油閥，而這些設備是由諸如商店或輕工工廠或農場的非人員使用的，也包含在本部分范圍內。本部分說明了一些機械特征在\"在考慮中\(zhòng)"。直到機械要求包含在本部分中，每個使用本部分的應說明這些要求。 1.1.2本部分適用于那些人工控制器，當其電氣上或機械上構成電動油閥。 本部分不適用于標稱連接尺寸在DN 150以上的電動油閥。\"閥\"一詞指電動油閥(包括原動機構和閥體組件)。 1.1.3與電動油閥一起送到測試試驗室的電起動器在本部分中評估。獨立的電起動器在GB 14536.16 中評估，該標準為電起動器的特殊要求。 1.1.4本部分適用于單個的閥、作為系統部件的閥和與多功能控制器機械地組合在一起的無電氣輸出的閥。

GB/T 30597-2014燃氣燃燒器和燃燒器具用安全和控制裝置通用要求

本標準規定了使用GB/T 13611規定的城鎮燃氣的燃氣燃燒器和燃燒器具用安全和控制裝置及其組件(以下簡稱“控制裝置”)的術語和定義、分類和分組、結構和材料、要求、試驗方法、標識、安裝和操作說明書、包裝、運輸和貯存。本標準適用于以下控制裝置:--自動和半自動閥;--燃燒控制裝置;--熄火保護裝置;--燃氣和空氣比例調節裝置;--壓力調節裝置;--旋塞閥總成;--溫度控制裝置;--多功能控制裝置;--壓力傳感裝置;--閥門檢驗系統。

HG/T 20505-2014過程測量與控制儀表的功能標志及圖形符號

本標準適用于化工自控設計中儀表回路號、儀表位號的編制以及儀表圖形符號的規定及應用。

CJ/T 336-2010冷凝式家用燃氣快速熱水器

本標準規定了加熱生活用水的冷凝式家用燃氣快速熱水器的分類和型號、材料和結構、要求、試驗方法、驗收規則及標志和說明書、包裝、運輸和貯存。本標準適用于除人工煤氣之外符合GB/T 13611規定燃氣、額定熱輸入不大于70kW的強制排氣式冷凝熱水器、強制給排氣式冷凝熱水器和室外型冷凝熱水器。

HB 7504.10-1997飛行模擬器設計和性能的數據要求 液壓系統

本標準規定了飛行模擬器液壓系統的數據要求?！　”緲藴蔬m用于民用飛機飛行模擬器，軍用模擬器可參照使用?！　”緲藴蕿轱w行模擬器承制方、使用方、飛機設備的訂購方和有關管理機構，提供建造和驗證符合空勤人員訓練要求的、足夠逼真的飛行模擬器所必須的數據范圍和內容?！　”緲藴什皇谴_定飛行模擬器數據要求的唯一方法。

SL/T 244-1999水文纜道機電設備及測驗儀器通用技術條件

本標準規定了適用于水面寬500m、水深30m,流速5m/s、吊重400kg以下的中小型江河水文纜道測驗設備及儀器的定義、分類、組成、型號命名、技術要求、試驗方法、檢驗規則及標志、包裝、運輸、貯存等要求。

NB/T 20358.8-2018核電廠建設工程預算定額 第8部分:核島自動化控制儀表安裝工程

本部分規定了核電廠建設工程預算定額中的核島自動化控制儀表安裝工程定額。本部分適用于壓水堆核電機組新建、擴建工程的核島工程，以及BOP工程中的核島廢液貯罐廠房、常規島廢液貯罐廠房、放射性固體廢物處理輔助廠房、固體廢物暫存庫、放射性機修及去污車間等有核安全要求的子項。其他核電堆型和核工程可參考使用。

EN 30-1-1-2008家用燃氣灶具.第1-1部分:安全性.一般性;包含修改件A1-2010

This European Standard specifies the construction and performance characteristics as well as the requirements and methods of test for the safety and marking of freestanding and built-in domestic cooking appliances burning the combustible gases given in 4.1 according to the categories specified in 4.2, referred to in the text as \"appliances\".This European Standard covers the following types of domestic cooking appliances, as defined in Clause 3, and belonging to the classes defined in 4.3 (see Table 1): independent freestanding hotplates; independent built-in hotplates; independent hotplates and grills; table cookers; freestanding ovens; built-in ovens; freestanding or built-in grills; griddles; freestanding cookers; built-in cookers. Unless specifically excluded hereafter,This European Standard applies to these appliances or their component parts, whether or not the component parts are independent or incorporated into a single appliance, even if the other heating components of the appliance use electrical energy (e. g. combined gas-electric cookers).This European Standard includes requirements covering the electrical safety of equipment incorporated in the appliance that is associated with the use of gas. It does not include requirements covering the electrical safety of electrically-heated component parts or their associated equipment1).This European Standard does not apply to: a) outdoor appliances; b) appliances connected to a combustion products evacuation duct; c) appliances having a pyrolitic gas oven; d) appliances having covered burners which are not in conformity with the constructional requirements of 5.2.8.2.2; e) appliances incorporating flame supervision devices and having an automatic ignition device for which the duration of the ignition attempt is limited by design; f) appliances equipped with a burner that is periodically ignited and extinguished under the control of an automatic on/off device; 1) Refer to the electrical safety rules. g) appliances equipped with an oven and/or with a grill having a fan: 1) either for the supply of combustion air or for the evacuation of the products of combustion; 2) or for the circulation of the products of combustion within the compartments; h) appliances supplied at pressures greater than those defined in 7.; i) appliances having one or more burners that are capable of remote operation (type1 or type 2), unless the burner(s) concerned are thermostatically controlled oven burners of time-controlled ovens that are designed for a delayed start without the user being present; j) appliances incorporating one or more hotplate or grill burners that enable the user to program the cooking cycle, including the start and/or the end of the cycle.This European Standard does not cover the requirements relating to third family gas cylinders, their regulators and their connection.This European Standard only covers type testing.

NF D35-354-2008專用液化石油氣裝置用規范.家用無煙道空間加熱器(包括擴散式催化燃燒加熱器)

La présente Norme européenne spécifie les prescriptions, les méthodes d'essais et le marquage des appareils domestiques de chauffage non raccordés à un conduit d'évacuation des produits de la combustion, y compris les appareils à combustion catalytique diffusive, dont le débit calorifique nominal est inférieur à 4,2 kW (HS), alimentés par des gaz de la 3e famille sous la pression nominale de service ne dépassant pas 50 mbar, désignés dans le texte par \"appareils\".La présente Norme européenne est applicable aux types d'appareils suivants : appareils fixes fonctionnant au butane commercial et/ou au propane commercial ; appareils portatifs ou mobiles fonctionnant soit au butane commercial, soit au butane commercial et au propane commercial, y compris ceux qui ont un compartiment d'installation pour une bouteille portative rechargeable de gaz de pétrole liquéfié.Aucune prescription particulière concernant le rendement thermique n'est définie pour ces types d'appareils car toute la chaleur produite par le processus de la combustion se dégage dans l'espace à chauffer ; les exigences concernant la combustion, qui relèvent de la sécurité, garantissent la combustion du combustible gazeux.La présente Norme européenne ne concerne pas les appareils incorporant des dispositifs électriques de contr?le du gaz.L'annexe A donne les détails concernant les catégories d'appareils commercialisées dans les divers pays.Les exigences pour les appareils données dans cette norme européenne supposent que l'alimentation en gaz à partir de la bouteille soit contr?lée par un détendeur dont la pression nominale maximale de détente atteint 50 mbar.La présente norme européenne ne concerne pas les bouteilles de gaz de pétrole liquéfié, ni leurs détendeurs associés, ni les tubes et tuyaux flexibles, qui doivent être conformes aux réglementations nationales en vigueur. La présente norme couvre uniquement les essais de type.

DIN EN 449-2008專用液化石油氣裝置用規范.無排氣口的居室暖器(包括擴散催化燃燒的加熱器)

This European Standard specifies the requirements, the test methods and the marking of domestic flueless spaceheaters, including diffusive catalytic combustion heaters, having a nominal heat input (Hs), not exceeding 4,2 kWburning 3rd family gases at nominal operating pressures not exceeding 50 mbar. referred to in the text as'appliances'.This European Standard is applicable to the following types of appliances:a) fixed heaters burning commercial butane and/or commercial propane;b) portable or mobile heaters burning either commercial butane, or, commercial butane and commercial propane including those that incorporate a LPG container installation compartment for a transportable refillable liquefied petroleum LPG container.There are no specific thermal efficiency requirements appropriate to these types of appliance as:c) all the heat produced by the combustion process is released into the space to be heated;d) the requirements with regard to the combustion performance, which is a safety matter, ensure the effective burning of the fuel gas.It does not cover appliances incorporating electrically operated gas control systems.Annex A gives the details of the categories of appliances marketed in various countries.Requirements for appliances given in this standard assume that the supply of gas from the container will begoverned by a pressure regulator having a maximum nominal outlet pressure of 50 mbar.This European Standard does not cover LPG containers for liquefied petroleum gas neither their associatedregulator nor tubing and flexible hoses which shall comply with national requirements in force.This European Standard only covers type testing.

DIN EN 13278-2014前開式獨置燃氣加熱器.德文版本EN 13278-2013

This European Standard specifies the requirements and test methods for the construction, safety, marking and rational use of energy of open fronted gas-fired independent space heaters with and without a fan to assist with the transportation of flue gases. Although the fan may be mounted outdoors, this standard only covers appliances where the body of the appliance is indoors. This standard applies to types B11AS, B11BS, B14AS, and B14BS open fronted gas-fired independent space heating appliances that incorporate an atmospheric burner, that are connected directly to an open flue or to a device to evacuate the products of combustion (open-flued appliances), that have a nominal heat input not exceeding 20 kW (based on the net calorific value) and that are delivered with the gas-carrying components, burner (s), combustion chamber and heat exchanger fully assembled.

BS EN 449-2002+A1-2007專用液化石油氣設施的規范.家用無煙道空間加熱器(包括擴散式催化燃燒加熱器)

This European Standard specifies the requirements, the test methods and the marking of domestic flueless spaceheaters, including diffusive catalytic combustion heaters, having a nominal heat input (Hs), not exceeding 4,2 kWburning 3rd family gases at nominal operating pressures not exceeding 50 mbar, referred to in the text as'appliances'.This European Standard is applicable to the following types of appliances:a) fixed heaters burning commercial butane and/or commercial propane;b) portable or mobile heaters burning either commercial butane, or, commercial butane and commercial propaneincluding those that incorporate a LPG container installation compartment for a transportable refillable liquefiedpetroleum LPG container.There are no specific thermal efficiency requirements appropriate to these types of appliance as:c) all the heat produced by the combustion process is released into the space to be heated;d) the requirements with regard to the combustion performance, which is a safety matter, ensure the effectiveburning of the fuel gas.It does not cover appliances incorporating electrically operated gas control systems.Annex A gives the details of the categories of appliances marketed in various countries.Requirements for appliances given in this standard assume that the supply of gas from the container will begoverned by a pressure regulator having a maximum nominal outlet pressure of 50 mbar.This European Standard does not cover LPG containers for liquefied petroleum gas neither their associatedregulator nor tubing and flexible hoses which shall comply with national requirements in force.This European Standard only covers type testing.

BS EN 656-2000燃氣集中供暖鍋爐.標稱熱輸入值70KW-300KW的B型鍋爐

This standard specifies the requirements and test methods concerning, in particular the construction, safety, fitness for purpose, and rational use of energy, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as \"boilers\".\nThis standard applies to boilers of type B, as listed in 4.2:\n- that use one or more combustible gases of the three gas families at the pressures stated in Tables 14 and 15;\n- that have a nominal heat input (net CV basis) exceeding 70 kW, but not exceeding 300 kW, including modular boilers;\n- where the temperature of the heat transfer fluid does not exceed 105 ℃ during normal operation;\n- where the maximum operating pressure in the water circuit does not exceed 6 bar.\nThe standard applies to boilers designed for sealed water systems or for open water systems.\nThe standard does not contain all the requirements necessary for boilers:\n- intended to be installed in the open or in living rooms;\n- permanently fitted with more than one flue outlet;\n- where the combustion circuit is sealed with respect to the room where the boiler is installed;\n- of the condensing type;\n- of the low temperature type;\n- intended to be connected to a common flue having mechanical extraction;\n- fitted with a forced draught burner in accordance with EN 676;\n- producing hot water for domestic purposes.\nThis standard only covers type testing.