電氣和電子設備用機電開關檢測

電氣和電子設備用機電開關檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 9536-2012電氣和電子設備用機電開關.第1部分：總規范

本部分規定了電氣和電子設備用的機電開關。 本部分適用的開關: a)借助導電部件（觸頭）的機械運動來斷開、接通或轉換電路連接的裝置；b)大額定電壓為480V；c)大額定電流為63A。本部分不適用于供信息處理系統使用的鍵盤和輔助鍵盤。本部分也可適用于機電琴鍵（按鍵）開關。開關系列將在對應本總規范的詳細規范中描述。

GB/T 22663-2008工業機械電氣設備.電磁兼容.機床抗擾度要求

本標準規定了用于工業環境或類似用途，線間額定電壓不超過1000Va.c或者1500Vd.c的機床電磁兼容的抗擾度要求。本抗擾度標準也可用于評估在其他環境中使用的機床，這些環境（住宅、輕工業環境等）比工業環境要求的抗擾度水平低。本標準不適用于安裝在特殊的電磁環境中的機床，例如：存在強電磁場（如在廣播發射臺附近），或在有電力網強脈沖環境（如發電站）的機床。在這些場合中使用的設備及系統，需采取相應的降低電磁影響的措施。本標準涉及電磁抗擾度的頻率范圍為0Hz至400GHz。其他頻率不在標準考慮之列。

GB 23712-2009工業機械電氣設備.電磁兼容.機床發射限值

本標準規定了用于工業環境或類似用途，線間額定電壓不超過1000Va.c.或者1500Vd.c.的機床的電磁發射限值，但不包括電火花加工機床(EDM)。本標準涉及電磁發射的頻率范圍為9 kHz~400GHz。其他頻率不在本標準考慮之列。

JB/T 13034-2017器具電子開關電氣性能要求及試驗方法

本標準規定了器具電子開關進行開關功能操作、發熱、耐久性、電子開關的不正常工作和故障條件、控制特性、保護特性、開關電子器件壽命試驗等電氣性能試驗的電氣性能要求、試驗方法和檢驗規則。本標準適用于器具開關中的電子開關(以下簡稱開關)進行電氣性能設計、試驗時的要求及試驗方法，這些電子開關包括獨立安裝的、附裝的、拼合的或者靠激發傳感器(可在實體上或電氣上與開關結合在一起，也可分開配置，還可能包含操動件或傳感器與開關之間的信號傳輸，例如，電氣的、光的、聲的或溫度的信號傳輸)操作的開關。在特殊環境下使用的器具電子開關電氣性能要求及試驗方法也可參照?qǐng)?zhí)行。

DL/T 593-2016高壓開關設備和控制設備標準的共用技術要求

本標準適用于電壓3.0kV及以上、頻率為50Hz的電力系統中運行的戶內和戶外交流高壓開關設備和控制設備。除非在特定類型開關設備和控制設備有關的產品標準中另有規定，本標準適用于所有的高壓開關設備和控制設備。

EN 746-2-2010工業熱加工工藝設備.燃燒和燃料儲運系統安全要求

This part of EN 746 together with EN 746-1 specifies safety requirements for single and multiple burners that are part of Industrial Thermoprocessing Equipment. (InThis standard referred to as IThE).This document deals with significant hazards, hazardous situations and events relevant to combustion and fuel handling systems that are part of IThE as listed in Clause 4, when used as intended and under the conditions foreseen by the manufacturer.This European Standard covers: fuel pipework downstream of and including the manual isolating valve; burner(s), burner system and ignition device; safety related control system (protective system).This European Standard applies to any oxidation with air or other gases containing free oxygen of gaseous, liquid and solid fuels or any combustion of them to release thermal energy. For thermal or catalytic post combustion and waste incineration,This European Standard applies only to auxiliary burners designed to start-up and/or support the process. The pressure hazard of the piping and components covered byThis standard is within the limits of maximum pressure/size relationship as described in normative Annex E.This European Standard also gives the necessary requirements for the information for use.This European Standard does not cover hazards from heating generated by electricity.This European Standard does not deal with the hazards created by the release of flammable substances from the products processed in the IThE. NOTE EN 1539, Dryers and ovens, in which flammable substances are released-Safety requirementsThis European Standard is not applicable to combustion and fuel handling systems of welding and soldering machines; up-stream of the IThE manual isolating valve.This European Standard is not applicable to electricity cabling and power cabling upstream of the IThE control panel/protective system. Noise can be a significant hazard for combustion and fuel handling systems. It is not dealt with inThis standard.This European Standard is not applicable to combustion and fuel handling systems as part of IThE which is manufactured before the date of its publication as EN.

GSO IEC 61020-1-2014電氣和電子設備用機電開關.第1部分：總規范

This generic specification relates to electromechanical switches intended for use in electrical and electronic appliances. Switches covered by this specification: a) are devices which open, close, or change the connection of a circuit by the mechanical motion of conducting parts (contacts); b) have a maximum rated voltage of 480 V; c) have a maximum rated current of 63 A. This generic specification does not include keyboards and keypads which are intended for use in information-handling systems. Electromechanical key switches may be included under the scope of this generic specification. Switch families shall be described in any detail specifications that will reference this generic specification.

NF C83-410-1-2019電氣和電子設備的機電開關. 第1部分: 總規范

Domaine d'applicationLa présente partie de l'IEC 61020 spécifie la terminologie, les symboles, les méthodes d'essai et d'autres informations nécessaires pour assurer la cohérence des spécifications particulières applicables aux interrupteurs électromécaniques.Le présent document concerne les interrupteurs électromécaniques destinés à être utilisés dans les dispositifs électriques et électroniques. Les interrupteurs relevant du présent document:sont des dispositifs qui ouvrent, ferment ou commutent un circuit par le mouvement mécanique de leurs parties conductrices (contacts) ;ont une tension assignée maximale de 480 V;ont un courant assigné maximal de 63 A.Le présent document ne s'applique pas aux claviers prévus pour être utilisés dans les systèmes de traitement de l'information. Les interrupteurs électromécaniques à touche peuvent relever du domaine d'application du présent document.Les familles d'interrupteurs sont décrites dans des spécifications particulières faisant référence au présent document.Le présent document est une norme de qualité de fonctionnement destinée à décrire les méthodes d'appréciation afin de clarifier les capacités d'un interrupteur.Les exigences relatives à la sécurité des interrupteurs pour installations électriques fixes domestiques et analogues sont données dans l'IEC 60669 (toutes les parties) .Les exigences relatives à la sécurité des interrupteurs pour appareils sont données dans l'IEC 61058 (toutes les parties) .

DIN EN 746-2-2011工業熱處理設備.第2部分:燃燒和燃料處理系統的安全要求;德文版本EN 746-2-2010

This part of EN 746 together with EN 746-1 specifies safety requirements for single and multiple burners that are part of Industrial Thermoprocessing Equipment. (In this standard referred to as IThE).This document deals with significant hazards, hazardous situations and events relevant to combustion and fuel handling systems that are part of IThE as listed in Clause 4, when used as intended and under the conditions foreseen by the manufacturer.This European Standard covers:- fuel pipework downstream of and including the manual isolating valve;- burner(s), burner system and ignition device;- safety related control system (protective system).This European Standard applies to any oxidation with air or other gases containing free oxygen of gaseous, liquid and solid fuels or any combustion of them to release thermal energy.For thermal or catalytic post combustion and waste incineration, this European Standard applies only to auxiliary burners designed to start-up and/or support the process.The pressure hazard of piping and components covered by this standard is within the limits of maximum pressure/size relationship as described in normative Annex E.This European Standard also gives the necessary requirements for the information for use.This European Standard does not cover hazards from heating generated by electricity.This European Standard does not deal with the hazards created by the release of flammable substances from the products processed in the IThE.This European Standard is not applicable to electricity cabling and power cabling upstream of the IThE control panel/protective system.Noise can be a significant hazard for combustion and fuel handling systems. It is not dealt with in this standard.This European Standard is not applicable to combustion and fuel handling systems as part of IThE which is manufactured before the date of its publication as EN.

DIN EN 62047-5-2012半導體器件.微電機裝置.第5部分:射頻(RF)微電子機械系統(MEMS)開關(IEC 62047-5-2011).德文版本 EN 62047-5-2011

This standard describes terminology, definition, symbols, test methods that can be used to evaluate and determine the essential ratings and characteristic parameters of RF MEMS switches.

BS EN 746-2-2010工業熱加工設備.燃燒和燃料處理系統的安全性要求

This part of EN 746 together with EN 746-1 specifies safety requirements for single and multiple burners thatare part of Industrial Thermoprocessing Equipment. (In this standard referred to as IThE).This document deals with significant hazards, hazardous situations and events relevant to combustion andfuel handling systems that are part of IThE as listed in Clause 4, when used as intended and under theconditions foreseen by the manufacturer.This European Standard covers:? fuel pipework downstream of and including the manual isolating valve;? burner(s), burner system and ignition device;? safety related control system (protective system).This European Standard applies to any oxidation with air or other gases containing free oxygen of gaseous,liquid and solid fuels or any combustion of them to release thermal energy.For thermal or catalytic post combustion and waste incineration, this European Standard applies only toauxiliary burners designed to start-up and/or support the process.The pressure hazard of the piping and components covered by this standard is within the limits of maximumpressure/size relationship as described in normative Annex E.This European Standard also gives the necessary requirements for the information for use.This European Standard does not cover hazards from heating generated by electricity.This European Standard does not deal with the hazards created by the release of flammable substances fromthe products processed in the IThE.This European Standard is not applicable to combustion and fuel handling systems? of welding and soldering machines;? up-stream of the IThE manual isolating valve.This European Standard is not applicable to electricity cabling and power cabling upstream of the IThE controlpanel/protective system.Noise can be a significant hazard for combustion and fuel handling systems. It is not dealt with in thisstandard.This European Standard is not applicable to combustion and fuel handling systems as part of IThE which ismanufactured before the date of its publication as EN.

BS EN 50370-1-2005電磁兼容性(EMC).機床用產品系列標準.排放

This standard deals with the electromagnetic emission (radio frequency protection) of machine tools, excluding electro discharge machines (EDM), designed exclusively for industrial and similar purposes that use electricity, the rated voltage of the machine tool not exceeding 1 000 V AC or 1 500 V DC between lines.\nMachine tools may incorporate motors, heating elements or their combination, may contain electric or electronic circuitry, and may be powered by the mains, or any other electrical power source.\nThis standard does not cover fixed installations as defined in the Guide to the Application of Directive 89/336/EEC, published by the European Commission.\nEmission requirements in the frequency range 9 kHz to 400 GHz are covered. No measurements need to be performed at frequencies where no requirements are specified.

BS EN 50370-2-2003電磁兼容性(EMC).機床用產品系列標準.抗擾性

This standard deals with the electromagnetic immunity of machine tools designed exclusively for industrial and similar purposes that use electricity, the rated voltage of the machine tool not exceeding 1 000 V a.c. or 1 500 V d.c. between lines.\nMachine tools may incorporate motors, heating elements or their combination, may contain electric or electronic circuitry, and may be powered by the mains, or any other electrical power source.\nThis immunity standard may also be used for assessment of equipment used in other environments, which require less stringent immunity levels (residential, light industry...) than the industrial environment.\nThis standard is not intended for the EMC conformity assessment of modules to be placed on the market separately.\nThis standard is not intended for complying with Machinery Directive 98/37/EC. Hence safety considerations are not covered by this standard.\nThis standard does not cover fixed installations as defined in the Guide to the Application of Directive 89/336/EEC, published by the European Commission.\nThis standard does not apply to apparatus intended to be used in locations where special electromagnetic conditions prevail, such as the presence of high electromagnetic fields (e.g. in the vicinity of a broadcast transmitting station) or where high pulses occur on the power network (e.g. in a power generator station). In these instances special mitigation measures may have to be employed.\nImmunity requirements in the frequency range 0 Hz to 400 GHz are covered. No measurements need to be performed at frequencies where no requirements are specified.