歡迎訪問中科光析科學技術研究所官網！
- 聯系我們
- 關注微信
歡迎訪問中科光析科學技術研究所官網！
免費咨詢熱線
400-635-0567|
農業灌溉設備 灌溉閥 隔離閥檢測項目報價？??解決方案？??檢測周期？??樣品要求？ |
點 擊 解 答?? |
本文件規定了隔離閥的設計要求、性能要求、一致性評定、標志和包裝。該隔離閥適用于水溫不超過60 ℃，并且水中可能含有某些農業常用類型和濃度的肥料或化學物質的灌溉系統。本文件適用于公稱尺寸不小于DN 8的灌溉隔離閥，該隔離閥的設計工作狀態為全開和全關，但也可在任意中間狀態長時間工作。
本標準規定了壓力灌溉系統中水頭控制器的零部件要求以及安裝方法（簡稱為灌溉水頭控制器，其標準尺寸不大于200mm)。本標準僅適用于噴灌和微灌（小型噴灌、滴灌等）系統中水頭控制器的地上零部件。也可適用于一般性的灌溉水頭控制器。在一般性的灌溉水頭控制器上可安裝其他的灌溉控制和指令元件（例如電氣、電子、水力），但不能用于額外元件。本標準不適用于系統和/或元件中的灌溉水頭控制器有防凍要求的情況，例如干筒式水栓或其他形式的水栓。本標準沒有給出組成灌溉水頭控制器的單個元件的特殊設計及操作要求的說明，在其各自相關標準給出詳細說明。對于包含噴射農藥部件系統的灌溉水頭控制器，應設有防回流的元件及噴射檢測閥和其他安全設備（根據當?shù)貥?biāo)準和條款要求），但本標準中沒有包含此類設備要求。
本標準規定了農業灌溉設備的常用術語和定義。本標準適用于節水灌溉設備(包括噴灌機、噴灌泵、噴灌管路、噴頭等設備)設計、制造和試驗。
本標準規定了農業灌溉設備評價用試驗裝置系統組件的設計、選擇、安裝和使用指南。本標準適用于GB/T 17187、ISO 15886、GB/T 19794、GB/T 19793、GB/T 18688、GB/T 18689、GB/T 18691和GB/T 18692規定的試驗方法，給農業灌溉系統組件，特別是滴頭、噴頭和閥的試驗提供足夠的信息。
GB/T 36702的本部分規定了化學灌溉用小型塑料閥(以下簡稱“裝置”)的一般要求和試驗方法。該裝置用于可能含有某些農業常用類型和濃度的肥料或化學物質的灌溉管路系統中。本部分適用于帶減壓區(RPZ)的可控安全裝置(還被稱為回流防止器)。該裝置用于防止當上游飲用水分配系統壓力低于下游系統壓力時，因倒吸或背壓導致灌溉水回流進入上游飲用水分配系統。本部分適用于公稱尺寸不大于DN50，公稱壓力為PN10，并且在下列情況下不需修正或調整能夠工作的裝置：——壓力在1 MPa以下；——壓力變化量不大于1 MPa；——溫度不大于45 ℃環境下長期工作，溫度在65 ℃下工作1 h。
This part of ISO 9635 specifies construction and performance\nrequirements and test methods for isolating valves, intended for\noperation in irrigation systems with water at temperatures not\nexceeding 60 °C, which can contain fertilizers and other chemicals\nof the types and concentrations used in agriculture.\nIt is applicable to isolating irrigation valves of DN 8 in\ndiameter or greater, designed to operate in the fully open and\nfully closed positions, but which can also operate for extended\ntime periods in any intermediate position.
This document applies to irrigation hydrants intended to supply equipment for use in water distribution irrigation networks. The range of PN is that defined in EN 1074-1, i.e.: PN 10, PN 16, PN 25 and limited to PN 25.
This part of ISO 9635 specifies construction and performance requirements and test methods for isolating valves, intended for operation in irrigation systems with water at temperatures not exceeding 60 °C, which can contain fertilizers and other chemicals of the types and concentrations used in agriculture. It is applicable to hydraulically operated isolating irrigation valves of DN 8 (1/4 inch) diameter or greater, designed to operate in the fully open and fully closed positions, but which can also operate for extended time periods in any intermediate position.
This part of ISO 9635 specifies construction and performance requirements and test methods for isolating valves, intended for operation in irrigation systems with water at temperatures not exceeding 60 ?C, which can contain fertilizers and other chemicals of the types and concentrations used in agriculture.
Specifies construction and performance requirements and test methods for isolating valves, intended for operation in irrigation systems with water at temperatures not exceeding 60 which can contain fertilizers and other chemicals of the types and co
