建筑石膏參數檢測

建筑石膏參數檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 17669.4-1999建筑石膏 凈漿物理性能的測定

本標準規定了建筑石膏凈漿的標準稠度用水量和凝結時間的測定方法。

CJJ/T 230-2015排水工程混凝土模塊砌體結構技術規程

本規程適用于內壓不大于0.06MPa的矩形排水管渠和檢查井、內水深度不大于4m的排水構筑物等排水工程混凝土模塊砌體結構的設計、施工及驗收。

HB/Z 248-1993飛機裝配型架設計

本標準規定了飛機及其他飛行器裝配型架（以下簡稱型架）設計的主要技術要點。\n　　本標準適用于飛機裝配型架設計。

JC/T 2581-2021建筑石膏煅燒設備 沸騰爐

本文件規定了建筑石膏煅燒設備沸騰爐的術語和定義、型號和基本參數、技術要求、試驗方法、檢驗規則以及標志、包裝、運輸和貯存。本文件適用于以熱風為熱源的建筑石膏煅燒設備沸騰爐(以下簡稱沸騰爐)。

SB/T 10647-2011干混砂漿質量管理規程

本標準規定了總則、術語、分類與標記、生產過程質量管理、產成品質量管理、運輸和貯存質量管理、施工過程質量管理。本標準適用于干混砂漿在生產、檢驗、物流及施工過程中的質量控制與管理。

SN/T 2297.1-2009進出口石膏及石膏制品化學分析方法 第1部分:鍶含量的測定

SN/T 2297的本部分規定了電感耦合等離子原子發射光譜、電感耦合等離子體質譜法和火焰原子吸收光譜法測定石膏及石膏制品中鍶含量的方法。

JG/T 169-2016建筑隔墻用輕質條板通用技術要求

本標準規定了建筑隔墻用輕質條板(以下簡稱輕質條板)的術語和定義、分類與標記、一般要求、要求、試驗方法、檢驗規則、標志、運輸和貯存。本標準適用于一般工業與民用建筑非承重隔墻輕質條板的生產與檢驗。

JGJ/T 181-2009房屋建筑與市政基礎設施工程檢測分類標準

本標準適用于房屋建筑和市政基礎設施工程檢測的分類。

JGJ/T 220-2010抹灰砂漿技術規程

本規程適用于新建、改建、擴建和既有建筑的一般抹灰工程用砂漿的配合比設計、施工及質量驗收。

JGJ/T 240-2011再生骨料應用技術規程

本規程適用于再生骨料在建筑工程中的應用。

JGJ/T 261-2011外墻內保溫工程技術規程

本規程適用于以混凝土或砌體為基層墻體的新建、擴建和改建居住建筑外墻內保溫工程的設計、施工及驗收。

DB31/T 666-2012免煅燒脫硫石膏基衍生產品(粉刷砂漿、石膏砌塊和土壤固化劑)應用技術規程

本標準規定了免煅燒脫硫石膏基衍生產品(粉刷砂漿、石膏砌塊和土壤固化劑)的術語和定義、材料、設計、施工和驗收要求。本標準適用于：1)　新建、改建、擴建及房屋修繕的民用建筑內墻和頂棚抹灰為主的免煅燒脫硫石膏基粉刷砂漿工程；2)　抗震設防烈度為8度及8度以下地區的工業與民用建筑中采用石膏砌塊砌筑的室內非承重墻體；3)　新建和改建各級城市道路、公路、建筑地基的固化土。

EN 1996-1-2-2005歐洲規范6.磚石工程結構設計.第1-2部分:一般規則.結構防火設計

(1)This Part 1-2 of EN 1996 deals with the design of masonry structures for the accidental situation of fire exposure, and is intended to be used in conjunction with EN 1996-1-1, EN 1996-2, 1996-3 and EN 1991-1-2.This part 1-2 only identifies differences from, or supplements to, normal temperature design. (2)This Part 1-2 deals only with passive methods of fire protection. Active methods are not covered. (3)This Part 1-2 applies to masonry structures which, for reasons of general fire safety, are required to fulfil certain functions when exposed to fire, in terms of: avoiding premature collapse of the structure (load bearing function); limiting fire spread (flames, hot gases, excessive heat) beyond designated areas (separating function) (4)This Part 1-2 gives principles and application rules for designing structures for specified requirements in respect of the aforementioned functions and levels of performance. (5)This Part 1-2 applies to structures, or parts of structures, that are within the scope of EN 1996-1-1, EN 1996-2 and EN 1996-3 and are designed accordingly. (6)PThis Part 1-2 does not cover masonry built with Natural Stone units to EN771-6 (7)PThis Part 1-2 deals with the following; non-loadbearing internal walls; non-loadbearing external walls; loadbearing internal walls with separating or non-separating functions; loadbearing external walls with separating or non-separating functions.

DIN 4102-4-2016建筑材料和建筑構件的耐火性能.概要和分級的建筑材料、構件和特種構件的應用

This document contains catagorized results of fire tests of buildings materials, components and construction types. Due to the assignment to the classes of building materials according to DIN 4102 part 1 and the fire resistance classes of the other parts of DIN 4102 respectively, further fire tests for the verification of usability required by the building regulations are not necessary.

DIN 4109-33-2016建筑物隔聲. 第33部分: 隔聲驗證使用數據 (組件目錄). 木結構, 輕型結構和干墻

This standard contains sound insulation specifications of components and structures for timber construction, lightweight construction and dry walling, which may be used without acoustic testing in the calculation procedures stated in DIN 4109-2 for the verification of the requirements of DIN 4109-1.

DIN 18180-2014石膏板.類型和要求

The standard applies to factory-produced gypsum plasterboards which are made of two sheets of mill-board affixed firmly to a layer of gypsum plaster between them. Gypsum plasterboards for various applications are defined, including those used as dry lining with or without additional fire resistance properties and those used as baseboards for plaster. Dimensions, mass in relation to surface, failure loads and degrees of deflection are given.

DIN EN 1996-1-2-2011歐洲法規6:圬工結構的設計.第1-2部分:一般規則.防火結構設計.德文版本EN 1996-1-2-2005 + AC-2010

This Part 1-2 of EN 1996 deals with the design of masonry structures for the accidental situation of fire exposure, and is intended to be used in conjunction with EN 1996-1-1, en 1996-2, 1996-3 and EN 1991-1-2. This part 1-2 only identifies differences from, or supplements to, normal temperature design.

DIN-Fachbericht CEN/TR 15125-2005內部水泥和/或石灰抹灰系統的設計、制備和應用

The Technical Report concerns the design, preparation and application of internal plaster and plastering systems based on cement and/or lime for internal plastering on all types of background used under normal conditions.#,,#

BS EN 1996-1-2-2005歐洲規范 6.磚石工程結構的設計.一般規則.結構防火設計

(1)P This Part 1-2 of EN 1996 deals with the design of masonry structures for the accidentalsituation of fire exposure, and is intended to be used in conjunction with EN 1996-1-1, EN1996-2, 1996-3 and EN 1991-1-2. This part 1-2 only identifies differences from, orsupplements to, normal temperature design.(2)P This Part 1-2 deals only with passive methods of fire protection. Active methods are notcovered.(3)P This Part 1-2 applies to masonry structures which, for reasons of general fire safety, arerequired to fulfil certain functions when exposed to fire, in terms of:- avoiding premature collapse of the structure (load bearing function)- limiting fire spread (flames, hot gases, excessive heat) beyond designated areas(separating function)(4)P This Part 1-2 gives principles and application rules for designing structures for specifiedrequirements in respect of the aforementioned functions and levels of performance.(5)P This Part 1-2 applies to structures, or parts of structures, that are within the scope ofEN 1996-1-1, EN 1996-2 and EN 1996-3 and are designed accordingly.(6)P This Part 1-2 does not cover masonry built with Natural Stone units to EN771-6(7)P This Part 1-2 deals with the following:- non-loadbearing internal walls.- non-loadbearing external walls.- loadbearing internal walls with separating or non-separating functions.- loadbearing external walls with separating or non-separating functions.